Klad is an engineered softwood board with a solid Oak wear layer, just like engineered flooring but for your stairs. Klad Treads, Risers and Extension Boards come Pre-finished in a clear satin lacquer - Select Single Sets or Packs of 3 Sets
Oak Stair Klad Treads are used with the Oak Stair Klad Risers, the treads are designed to push down onto the riser during installation.
Use 1000mm Treads and Risers for all standard steps up to 1000mm wide, simply cut your treads and risers to size and glue into position using polymer adhesive.
Use 1500mm Treads and Risers for steps wider than 1000mm, Winder Stairs and Kite Winders.
All Stair Klad Stair Cladding products are supplied Pre-finished in a clear satin lacquer.
Cheshire Mouldings Oak Stair Klad System is the perfect way to clad and create the warm and inviting look of an oak staircase without the expense and trouble of replacing your existing staircase.
Stair Klad Tread and Riser Usage
1000mm Treads and risers are used to clad your existing steps and riser boards that are up to 1000mm wide. If your existing step is deeper than 300mm the you will need to use the extension boards.
We suggest you measure the width of your steps and buy the 1500mm treads and risers only if your step is wider than 1000mm. When cladding a winder step you may find that they are deeper than the 300mm Stair Klad Tread, all you need to do in this instance is purchase a tongue and groove Klad extension board that connects to the back of the pre-grooved tread, extending it to the full width of your existing winder step.
Stair Klad Stair Cladding Fitting Guide
Before you start your stair cladding installation please read the instructions fully and contact us if you have any queries.
Before you start, ensure that your existing steps and riser boards are clean, dry and free from uneven defects. We suggest you thoroughly sand the steps to ensure you get a good sound base for your new Stair Klad Treads and Risers
Measure the existing bullnose protrusion from the face of the existing riser board to the furthest point of the bullnose on the existing step. You can then cut packing strips from timber that will push the bottom of the Stair Klad Riser board out and in line with the end of your bullnose. We suggest that these packing strips are screwed into place for stability.
Starting at the Top of the staircase, measure and cut three Stair Klad Risers to size and glue them onto the packing strips using
Measure the depth and width and cut a Stair Klad Tread to size. Apply a 10mm bead of Flexible Polymer Adhesive to the top of your existing step
Press the Stair Klad Tread onto the Adhesive firmly ensuring the Stair Klad Riser fits securely into the groove on the bottom of the Stair Klad Tread
Continue down the stairs fitting 3 riser boards first and then the treads.
If you reach a mid-landing, then use the same method above but use Klad Extension Boards to cover the landing area. These are supplied with a tongue and groove on the long edges that slot into the back edge of the tread.
If you have large Kite Winder Steps, then you may need to use the 1500mm wide Stair Klad Treads and Risers with Stair Klad Extension Boards. You can usually use 1000mm Treads and Risers with Extension Boards for triangular shaped winders no wider than 1000mm
Fix the stair Klad treads and any joining riser boards first then cut the extension boards to size, apply a good amount of polymer adhesive and push the boards together until the area is covered. Do not put adhesive between the T&G joints.
Work your way down the stairs to the bottom floor or use the Stair Klad Bottom Bullnose Step for cladding bullnose steps.
You can download the Cheshire Mouldings StairKlad Instructions manual from here.
Specification
Stair Klad Stair Cladding Specification
Supplied Pre-finished in a clear satin lacquer
Treads 1000mm or 1500mm Wide x 300mm Deep x 13.5mm Thick
Risers 1000mm or 1500mm Wide x 195mm High x 9mm Thick
Treads Pre-Grooved on the back edge for use with Extension Boards for landing areas and winder steps.
You can download the Cheshire Mouldings StairKlad Instructions manual from here.
